Logo Bihl+Wiedemann GmbH

Building Automation

The advantages of AS-Interface have now become familiar in Building Automation as well. The following overview shows the simple, cost-saving installation, and the high degree of flexibility of this industrial networking solution for automation systems:

(Klick zum Vergrößern)

AS-Interface – Building Automation

The advantages of AS-Interface – such as simple, cost-saving installation and high degree of flexibility – have now become familiar in Building Automation as well. Numerous companies are relying on the ASi installation system for applications such as controlling fire and smoke damper systems, shutter drives or heating and cooling ceilings using analog output modules. Damper actuators with flow regulators can also be connected to the controller through the MP-Bus Gateway. It is also possible to process EnOcean signals from wireless buttons and sensors through ASi. Customer proximity is our hallmark, which means we stand by you in word and deed and are open to custom-tailored solutions. Just contact us.

Basic Concept of AS-Interface 

AS-Interface is an industrial networking solution for automation systems. It is designed for connecting simple field I/O devices such as binary ON/OFF, analog and safety I/O devices according to EN 50295, IEC 62023-2. Using only a two conductor flat or round cable (ASi cable, 2 x 1.5 mm2, 16 AWG) to connect all slaves to the master using a free topology. This is the main advantage of this system compared to conventional, parallel wiring, where every single signal has to be wired directly to the control system.

Data and power are available in the same ASi cable . Every slave or module has its own address for accessing its data. The slaves can be addressed from 1 to 31 (single slaves), or, with extended addressing, there are 62 slaves available (1A to 31A and 1B to 31B). Single slaves and modules with extended addressing (AB modules) can share the same network.

The Structure

The ASi Master/Gateway controls the ASi network and acts as a direct link to the host (PLC, Building Management Systems, etc.). Combined with an integrated mini-PLC functionality the master can also be used for pre-processing or as a stand-alone device without the need for a host controller (programming language IL or C).

A Gateway is an ASi Master, and simultaneously a slave to higher level network (PROFIBUS, EtherNet/IP, Modbus, etc.). AS-Interface is the lowest level of the automation pyramid intended for Actuator/Sensor networking.


Free Topology

ASi supports free topology such as Star, Ring, Linear, Tree and Mesh  network (see examples below).

Tree topology

Ring topology


(Click to enlarge)

The simple and highly flexible ASi network bus is one of the great strengths of the system.  The master/slave principle allows the use of any topology and features a variety of different field and control cabinet modules. Whatever the requirements in your building we make it possible to record both digital and analog values and control either type of actuator. Whether a ventilation flap with four digital and four analog outputs, an analog output module for controlling heating/cooling ceilings, or special equipment such as an MP-Bus or EnOcean gateways.

You can also process both ASi standard and ASi Safety (up to SIL3) data over the same
Asi network. The data can be processed in the master or passed on to the higher level building management system through the fieldbus interface on the master.

ASi Characteristics


Unshielded two conductor flat cable *


*: Of course other cables such as NYM-J or E90 cables, can also be used.


Power Supply and data in one cable with max. 8 A

Number of Slaves per ASi Network

up to 62

Number of I/O Binary

up to 248 Inputs and 248 Outputs

Number of I/O Analog

up to 124 Inputs or Outputs

Cycle Time

153 µs/Slave

Transmission Rate

167 kbit/second

Error Protection

Identification and repetition of faulty frames

Supported Topology

Tree, Star, Ring, Linear, Linear with taps and Mesh


SIL 3, Category 4, PLe (EN 62061, EN 61508, EN ISO 13849-1, EN 954-1)

Cable Length

100 m (line extension possible using a bus termination, tuners and/or repeater up to 1000 m)

* Of course other cables, such as NYM-J or E90 cable, can also be used.


  • Gateways for linking to any Building Management System
  • Optionally with integrated controller (mini-PLC) also usable as stand-alone devices

(Click to enlarge)

  • 1 Master
  • 2 Masters
  • 2 Masters, Version "1 Gateway, 1 power supply for 2 ASi network”

(Click to enlarge)

Power Supplies

(Click to enlarge)

  • Single phase
  • 3 phases
  • 24 V to ASi
  • 1,8 A, 2 A, 4 A, 8 A
  • Decoupling unit for 2 ASi networks

    ASi Slaves

    Module for controlling damper actuators

    (Click to enlarge)

    • For ventilation, fire and smoke dampers
    • Inputs for end position detection
    • Additional input e.g. for fire alarms
    • Output for controlling dampers
    • Supply of the drives from ASi or external 24 V

    Module for increased safety requirements

    (Click to enlarge)

    • For ventilation, fire and smoke dampers according to Swiss standard for soldered strut and fire alarms
    • Inputs for end position detection
    • Control up to SIL 3/Cat. 4/PLe
    • Supply of the drives from ASi or external 24 V

    Module for controlling shutter drives

    (Click to enlarge)

    • 2 shutter drives (230 V AC) per module controllable
    • 4 inputs for switches
    • For 4-/5-conductor-shutters
    • Trip-/position recognition

    Relay Module for field applications (230V/24V)

    MP Bus Gateway

    EnOcean ASi Wireless Module

    (Click to enlarge)

    • Version with 2 relays and 4 inputs for e.g. damper actuators etc.
    • Version with 4 relays and 4 inputs for e.g. light, blower and fancoil control

    (Click to enlarge)

    • Linking MP-Bus participants (e.g. flow regulators) to ASi
    • Integrated 230 V / 24 V power supply

    (Click to enlarge)

      • For linking EnOcean wireless modules (e.g. pushbuttons, temperature sensors, window contacts, presence detectors) to ASi
    • Available in individual designs

    (Click to enlarge)

    • Up to 1922 safety I/Os per group

    (Click to enlarge)

    • ASi Safety Module to Control  Fire/SmokeDamper Actuators (up to SIL 2)

    (Click to enlarge)

    • Mixed Input / Output Modules
    • For floating contacts, OSSD outputs and safety mats
    • Electronic outputs
    • Relay outputs

    (Click to enlarge)

    • Speed/Standstill monitoring

    Digital and Analog Input and Output Modules

    In Stainless Steel, IP20

    (Click to enlarge)


    For example:

    • Digital 4I/4O
    • Digital 8I
    • Digital 8O
    • Relay outputs (230 V AC)

    In surface-mounted box, IP54

    (Click to enlarge)


    For example:

    • 2 analog (0-10 V) + 2 digital outputs for heating/cooling ceilings
    • Digital 4I/4O
    • Input Modules for CO2, relative humidity, etc.

    Coated module for flush-mounted boxes

    (Click to enlarge)

    • 4 digital inputs for standard switches

    Cabinet modules

    (Click to enlarge)

    • 4E/4A, 8E/8A
    • 0/4...20 mA
    • 0...10 V
    • Pt100, Pt1000
    • Thermocouples

    M12 Field Modules, IP67

    (Click to enlarge)

    • Digitale I/O Modules
    • Pt100, Pt1000
    • Analog  I/O Modules

    M12 Feldmodule, IP67

    Diagnostics/Circuit Extension

    (Click to enlarge)


    Bus Termination


    Repeater – optional with integrated Bus Termination

    (Click to enlarge)

    Benefits at a glance


    • Save hardware by reducing I/O cards, cabinets and wiring
    • Robust, globally standardized industrial bus with already more than 27 million installed nodes
    • Simple electronics with robust performance in industrial quality
    • Free choice of network topology
    • Quick installation, reduce maintenance and shorten testing time,fast commisioning and ability to expand the system
    • Easy commissioning, and opportunity to expand the system
    • Transmission in real-time
    • Avoid wiring errors (no risk of faulty electrical connection)
    • High resistance against EMC noise
    • Fast error localization, spontaneous diagnostics and enhanced diagnostic options


    ASi is fully backwards compatible. This means that a master according to the last specification 3.0 can communicate with all existing slaves according to the different specifications 2.0, 2.11 and 3.0. This guarantees a future proof investment.

    Simply to connect

    Owing to the yellow profile cable* and the piercing technology, ASi modules are easily expandable and can be connected reverse polarity protected.




    * Of course other cables, such as NYM-J or E90 cable, can also be used.

    Haben Sie Fragen zu unseren Produkten und Lösungen?